View SI5320-X-BC_1308958.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Si5320
SONET/SDH P R E C I S I O N C L O C K M U L T I P L I E R I C
Features
Ultra-low-jitter clock output with jitter generation as low as 0.3 psRMS No external components (other than a resistor and standard bypassing) Input clock ranges at 19, 39, 78, 155, 311, and 622 MHz Output clock ranges at 19, 155, or 622 MHz Digital hold for loss of input clock Support for forward and reverse FEC clock scaling Selectable loop bandwidth Loss-of-signal alarm output Low power Small size (9x9 mm)
Si5320 Si5320
Applications
SONET/SDH line/port cards Optical modules Core switches Digital cross connects Terabit routers
Ordering Information: See page 29.
Description
The Si5320 is a precision clock multiplier designed to exceed the requirements of high-speed communication systems, including OC-192/OC-48 and 10 GbE. This device phase locks to an input clock in the 19, 39, 78, 155, 311, or 622 MHz frequency range and generates a frequency-multiplied clock output that can be configured for operation in the 19, 155, or 622 MHz range. Silicon Laboratories' DSPLLTM technology delivers all PLL functionality with unparalleled performance while eliminating external loop filter components, providing programmable loop parameters, and simplifying design. FEC rates are supported with selectable 255/ 238 or 238/255 scaling of the clock multiplication ratios. The Si5320 establishes a new standard in performance and integration for ultra-low-jitter clock generation. It operates from a single 3.3 V supply.
Functional Block Diagram
REXT VSEL33 V DD GND
Biasing & Supply Regulation FXDDELAY CLKIN+ CLKIN- 2 CAL_ACTV
/
Signal Detect 3
M DSPLLT
DH_ACTV
/
Calibration
VALTIME LOS
2
CLKOUT+ CLKOUT- FRQSEL[1:0] RSTN/CAL
2
2
INFRQSEL[2:0]
FEC[1:0]
DBLBW
BWSEL[1:0]
Rev. 2.3 4/05
Copyright (c) 2005 by Silicon Laboratories
Si5320
Si5320
NOTES:
2
Rev. 2.3
Si5320 TABLE O F CONTENTS
Section Page
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.1. DSPLLTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 2.2. Clock Input and Output Rate Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 2.3. PLL Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.4. Digital Hold of the PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2.5. Hitless Recovery from Digital Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 2.6. Loss-of-Signal Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 2.7. Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2.8. PLL Self-Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2.9. Bias Generation Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 2.10. Differential Input Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2.11. Differential Output Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2.12. Power Supply Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2.13. Design and Layout Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 3. Pin Descriptions: Si5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 4. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 5. Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 6. 9x9 mm CBGA Card Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Rev. 2.3
3
Si5320
1. Electrical Specifications
Table 1. Recommended Operating Conditions
Parameter Ambient Temperature Si5320 Supply Voltage3 When Using 3.3 V Supply Symbol TA VDD33 Test Condition Min1 -202 3.135 Typ 25 3.3 Max1 85 3.465 Unit C V
Notes: 1. All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at nominal supply voltages and an operating temperature of 25 C unless otherwise stated. 2. The Si5320 is guaranteed by design to operate at -40 C. All electrical specifications are guaranteed for an ambient temperature of -20 to 85 C. 3. The Si5320 specifications are guaranteed when using the recommended application circuit (including component tolerance) of Figure 5 on page 15. 3.3 V operation uses an on-chip voltage regulator and is recommended.
4
Rev. 2.3
Si5320
C LKIN + C LKIN - V IS
A. O peration with Single-Ended C lock Input N ote: W hen using single-ended clock sources, the unused clock input on the Si5320 m ust be ac-coupled to ground.
C LKIN + C LKIN -
0.5 V ID
(C LKIN+) - (C LKIN -) V ID
B. O peration with D ifferential C lock Input N ote: Transm ission line term ination, when required, m ust be provided externally.
Figure 1. CLKIN Voltage Characteristics
80% 20% tF tR
Figure 2. Rise/Fall Time Measurement
(C L K IN + ) - (C L K IN - ) 0V
tLOS
Figure 3. Transitionless Period on CLKIN for Detecting a LOS Condition
Rev. 2.3
5
Si5320
Table 2. DC Characteristics, VDD = 3.3 V
(VDD33 = 3.3 V 5%, TA = -20 to 85 C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Supply Current 1 Supply Current 2 Power Dissipation Using 3.3 V Supply Clock Output Common Mode Input Voltage (CLKIN)
1,2,3
IDD IDD PD VICM VIS VID RIN VOD VOCM ISC(-) ISC(+) VIL VIH IIL IIH Ipd RIN VOL VOH
Clock in = 622.08 MHz Clock out = 19.44 MHz Clock in = 19.44 MHz Clock out = 622.08 MHz Clock in = 19.44 MHz Clock out = 622.08 MHz
-- -- -- 1.0
141 135 445 1.5 -- -- 80 906 1.8 -- 15 -- -- -- -- -- -- -- --
155 145 479 2.0 5004 5004 -- 1100 2.2 -- -- 0.8 -- 50 50 50 -- 0.4 --
mA mA mW V mVPP mVPP k mVPP V mA mA V V
A A A
Single-Ended Input Voltage2,3,4 (CLKIN) Differential Input Voltage Swing2,3,4 (CLKIN) Input Impedance (CLKIN+, CLKIN-) Differential Output Voltage Swing (CLKOUT) Output Common Mode Voltage (CLKOUT) Output Short to GND (CLKOUT) Output Short to VDD25 (CLKOUT) Input Voltage Low (LVTTL Inputs) Input Voltage High (LVTTL Inputs) Input Low Current (LVTTL Inputs) Input High Current (LVTTL Inputs) Internal Pulldowns (All LVTTL Inputs) Input Impedance (LVTTL Inputs) Output Voltage Low (LVTTL Outputs) Output Voltage High (LVTTL Outputs)
Notes:
See Figure 1A See Figure 1B
200 200 --
100 Load Line-to-Line 100 Load Line-to-Line
816 1.4 -60 -- -- 2.0 -- -- -- 50
k V V
IO = .5 mA IO = .5 mA
-- 2.0
1. The Si5320 device provides weak 1.5 V internal biasing that enables ac-coupled operation. 2. Clock inputs may be driven differentially or single-endedly. When driven single-endedly, the unused input should be ac coupled to ground. 3. Transmission line termination, when required, must be provided externally. 4. Although the Si5320 device can operate with input clock swings as high as 1500 mVPP, Silicon Laboratories recommends maintaining the input clock amplitude below 500 mVPP for optimal performance.
6
Rev. 2.3
Si5320
Table 3. AC Characteristics
(VDD33 = 3.3 V 5%, TA = -20 to 85 C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Input Clock Frequency (CLKIN) FEC[1:0] = 00 (non FEC) INFRQSEL[2:0] = 001 INFRQSEL[2:0] = 010 INFRQSEL[2:0] = 011 INFRQSEL[2:0] = 100 INFRQSEL[2:0] = 101 INFRQSEL[2:0] = 110 Input Clock Frequency (CLKIN) FEC[1:0] = 01 (forward FEC) INFRQSEL[2:0] = 001 INFRQSEL[2:0] = 010 INFRQSEL[2:0] = 011 INFRQSEL[2:0] = 100 INFRQSEL[2:0] = 101 INFRQSEL[2:0] = 110 Input Clock Frequency (CLKIN) FEC[1:0] = 10 (reverse FEC) INFRQSEL[2:0] = 001 INFRQSEL[2:0] = 010 INFRQSEL[2:0] = 011 INFRQSEL[2:0] = 100 INFRQSEL[2:0] = 101 INFRQSEL[2:0] = 110 Input Clock Rise Time (CLKIN) Input Clock Fall Time (CLKIN) Input Clock Duty Cycle CLKOUT Frequency FRQSEL[1:0] = 00 (no output) FRQSEL[1:0] = 01 FRQSEL[1:0] = 10 FRQSEL[1:0] = 11 CLKOUT Rise Time CLKOUT Fall Time Output Clock Duty Cycle RSTN/CAL Pulse Width Range*
fCLKIN
No FEC Scaling 19.436 38.872 77.744 155.48 310.97 621.95 -- -- -- -- -- -- 21.685 43.369 86.738 173.48 346.95 693.90 MHz
fCLKIN
255/238 FEC Scaling 18.142 36.284 72.568 145.13 290.27 580.54 -- -- -- -- -- -- 20.239 40.478 80.955 161.91 323.82 647.64 MHz
fCLKIN
238/255 FEC Scaling 20.826 41.652 83.305 166.61 333.22 666.44 -- -- -- -- -- -- -- -- 50 -- -- -- -- 213 191 -- -- 23.234 46.465 92.934 185.87 371.74 743.47 11 11 60 -- 21.685 173.48 693.90 260 260 52 -- MHz
tR tF CDUTY_IN
Figure 2 Figure 2
-- -- 40 -- 19.436 155.48 621.95
ns ns %
fO_19 fO_155 fO_622 tR tF CDUTY_OUT tRSTN Figure 2; single-ended; after 3 cm of 50 FR4 stripline Figure 2; single-ended; after 3 cm of 50 FR4 stripline Differential: (CLKOUT+) - (CLKOUT-)
MHz
-- -- 48 20
ps ps % ns
*Note: The Si5320 provides a 1/32, 1/16, 1/8, 1/4, 1/2, 1, 2, 4, 8, 16, or 32x clock frequency multiplication function with an option for additional frequency scaling by a factor of 255/238 or 238/255 for FEC rate compatibility.
Rev. 2.3
7
Si5320
Table 3. AC Characteristics (Continued)
(VDD33 = 3.3 V 5%, TA = -20 to 85 C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Transitionless Period Required on CLKIN for Detecting a LOS Condition. INFRQSEL[2:0] = 001 INFRQSEL[2:0] = 010 INFRQSEL[2:0] = 011 INFRQSEL[2:0] = 100 INFRQSEL[2:0] = 101 INFRQSEL[2:0] = 110 Recovery Time for Clearing an LOS Condition VALTIME = 0 VALTIME = 1
tLOS
Figure 3
16
24/
/fo_622 12 /fo_622 10/ fo_622 9 /fo_622 9 /fo_622 tVAL Measured from when a valid reference clock is applied until the LOS flag clears
fo_622
-- -- -- -- -- --
32
/fo_622 32 /fo_622 32/ fo_622 32 /fo_622 32 /fo_622
32/ fo_622
s
0.09 12.0
-- --
0.22 14.1
s
*Note: The Si5320 provides a 1/32, 1/16, 1/8, 1/4, 1/2, 1, 2, 4, 8, 16, or 32x clock frequency multiplication function with an option for additional frequency scaling by a factor of 255/238 or 238/255 for FEC rate compatibility.
8
Rev. 2.3
Si5320
Table 4. AC Characteristics (PLL Performance Characteristics)
(VDD33 = 3.3 V 5%, TA = -20 to 85 C)
Parameter Wander/Jitter at 800 Hz Bandwidth (BWSEL[1:0] = 10 and DBLBW = 0)
Symbol
Test Condition
Min
Typ
Max Unit
Jitter Tolerance (see Figure 7)
JTOL(PP)
f = 8 Hz f = 80 Hz f = 800 Hz
1000 100 10 -- -- -- -- -- -- -- -- -- --
-- -- -- 0.87 0.26 0.85 0.26 7.3 3.7 7.2 3.8 800 0.0
-- -- -- 1.2 0.35 1.2 0.35 10.0 5.0 10.0 5.0 -- 0.05
ns ns ns ps ps ps ps ps ps ps ps Hz dB
CLKOUT RMS Jitter Generation FEC[1:0] = 00 CLKOUT RMS Jitter Generation FEC[1:0 = 01, 10 CLKOUT Peak-Peak Jitter Generation FEC[1:0 = 00 CLKOUT Peak-Peak Jitter Generation FEC[1:0 = 01, 10 Jitter Transfer Bandwidth (see Figure 6) Wander/Jitter Transfer Peaking
Wander/Jitter at 1600 Hz Bandwidth (BWSEL[1:0] = 10 and DBLBW = 1)
JGEN(RMS) JGEN(RMS) JGEN(PP) JGEN(PP) FBW JP
12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz BW = 800 Hz < 800 Hz
Jitter Tolerance (see Figure 7)
f = 16 Hz f = 160 Hz f = 1600 Hz
500 50 5 -- -- -- -- -- --
-- -- -- 0.78 0.25 7.0 3.8 1600 0.00
-- -- -- 1.2 0.35 9.0 5.0 -- 0.05
ns ns ns ps ps ps ps Hz dB
CLKOUT RMS Jitter Generation FEC[1:0] = 00 CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 00 Jitter Transfer Bandwidth (see Figure 6) Wander/Jitter Transfer Peaking
JGEN(RMS) JGEN(PP) FBW JP
12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz BW = 1600 Hz < 1600 Hz
Notes: 1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient. 2. For reliable device operation, temperature gradients should be limited to 10 C/min. 3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude for the Si5320 (tPT_MTIE) never reaches one nanosecond.
Rev. 2.3
9
Si5320
Table 4. AC Characteristics (PLL Performance Characteristics) (Continued)
(VDD33 = 3.3 V 5%, TA = -20 to 85 C)
Parameter Wander/Jitter at 1600 Hz Bandwidth (BWSEL[1:0] = 01 and DBLBW = 0)
Symbol
Test Condition
Min
Typ
Max Unit
Jitter Tolerance (see Figure 7)
JTOL(PP)
f = 16 Hz f = 160 Hz f = 1600 Hz
1000 100 10 -- -- -- -- -- -- -- -- -- --
-- -- -- 0.82 0.26 0.79 0.26 7.3 3.8 7.1 4.3 1600 0.0
-- -- -- 1.0 0.35 1.0 0.35 10.0 5.0 10.0 5.0 -- 0.1
ns ns ns ps ps ps ps ps ps ps ps Hz dB
CLKOUT RMS Jitter Generation FEC[1:0] = 00 CLKOUT RMS Jitter Generation FEC[1:0] = 01, 10 CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 00 CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 01, 10 Jitter Transfer Bandwidth (see Figure 10) Wander/Jitter Transfer Peaking
Wander/Jitter at 3200 Hz Bandwidth (BWSEL[1:0] = 01 and DBLBW = 1)
JGEN(RMS) JGEN(RMS) JGEN(PP) JGEN(PP) FBW JP
12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz BW = 1600 Hz < 1600 Hz
Jitter Tolerance (see Figure 7)
f = 32 Hz f = 320 Hz f = 3200 Hz
500 50 5 -- --
-- -- -- 0.72 0.24
-- -- -- 0.9 0.3
ns ns ns ps ps
CLKOUT RMS Jitter Generation FEC[1:0] = 00
JGEN(RMS)
12 kHz to 20 MHz 50 kHz to 80 MHz
Notes: 1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient. 2. For reliable device operation, temperature gradients should be limited to 10 C/min. 3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude for the Si5320 (tPT_MTIE) never reaches one nanosecond.
10
Rev. 2.3
Si5320
Table 4. AC Characteristics (PLL Performance Characteristics) (Continued)
(VDD33 = 3.3 V 5%, TA = -20 to 85 C)
Parameter
Symbol
Test Condition
Min
Typ
Max Unit
CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 00 Jitter Transfer Bandwidth (see Figure 6) Wander/Jitter Transfer Peaking
Wander/Jitter at 3200 Hz Bandwidth (BWSEL[1:0] = 00 and DBLBW = 0)
JGEN(PP) FBW JP
12 kHz to 20 MHz 50 kHz to 80 MHz BW = 3200 Hz < 3200 Hz
-- -- -- --
6.8 3.7 3200 0.05
10.0 5.0 -- 0.1
ps ps Hz dB
Jitter Tolerance (see Figure 7)
JTOL(PP)
f = 32 Hz f = 320 Hz f = 3200 Hz
1000 100 10 -- -- -- -- -- -- -- -- -- --
-- -- -- 0.86 0.29 0.79 0.28 7.7 3.9 7.2 4.0 3200 0.05
-- -- -- 1.2 0.4 1.2 0.4 10.0 5.0 10.0 5.0 -- 0.1
ns ns ns ps ps ps ps ps ps ps ps Hz dB
CLKOUT RMS Jitter Generation FEC[1:0] = 00 CLKOUT RMS Jitter Generation FEC[1:0] = 01, 10 CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 00 CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 01, 10 Jitter Transfer Bandwidth (see Figure 6) Wander/Jitter Transfer Peaking
Wander/Jitter at 6400 Hz Bandwidth (BWSEL[1:0] = 00 and DBLBW = 1)
JGEN(RMS) JGEN(RMS) JGEN(PP) JGEN(PP) FBW JP
12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz BW = 3200 Hz < 3200 Hz
Jitter Tolerance (see Figure 7)
f = 64 Hz f = 640 Hz f = 6400 Hz
500 50 5 -- -- -- --
-- -- -- 0.7 0.25 6.6 3.8
-- -- -- 1.0 0.3 9.0 5.0
ns ns ns ps ps ps ps
CLKOUT RMS Jitter Generation FEC[1:0] = 00 CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 00
JGEN(RMS) JGEN(PP)
12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz
Notes: 1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient. 2. For reliable device operation, temperature gradients should be limited to 10 C/min. 3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude for the Si5320 (tPT_MTIE) never reaches one nanosecond.
Rev. 2.3
11
Si5320
Table 4. AC Characteristics (PLL Performance Characteristics) (Continued)
(VDD33 = 3.3 V 5%, TA = -20 to 85 C)
Parameter
Symbol
Test Condition
Min
Typ
Max Unit
Jitter Transfer Bandwidth (see Figure 6) Wander/Jitter Transfer Peaking
Wander/Jitter at 6400 Hz Bandwidth (BWSEL[1:0] = 11 and DBLBW = 0)
FBW JP
BW = 6400 Hz < 6400 Hz
-- --
6400 0.05
-- 0.1
Hz dB
Jitter Tolerance (see Figure 7) (1/1 Scaling)
JTOL(PP)
f = 64 Hz f = 640 Hz f = 6400 Hz
1000 100 10 -- -- -- -- -- -- -- -- -- --
-- -- -- 1.0 0.38 0.94 0.41 9.4 4.7 8.3 4.6 6400 0.05
-- -- -- 1.4 0.5 1.4 0.6 12.0 5.5 12.0 5.5 -- 0.1
ns ns ns ps ps ps ps ps ps ps ps Hz dB
CLKOUT RMS Jitter Generation FEC[1:0] = 00 (1/1 Scaling) CLKOUT RMS Jitter Generation FEC[1:0] = 01, 10 (255/238, 238/255 scaling) CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 00 (1/1 Scaling) CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 01, 10 (255/238, 238/255 scaling) Jitter Transfer Bandwidth (see Figure 6) Wander/Jitter Transfer Peaking
Wander/Jitter at 12800 Hz Bandwidth (BWSEL[1:0] = 11 and DBLBW = 1)
JGEN(RMS) JGEN(RMS) JGEN(PP) JGEN(PP) FBW JP
12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz BW = 6400 Hz < 6400 Hz
Jitter Tolerance (see Figure 7)
f = 128 Hz f = 1280 Hz f = 12800 Hz
500 50 5 -- -- -- -- -- --
-- -- -- 0.74 0.30 6.9 4.0 12800 0.05
-- -- -- 1.0 0.4 9.0 5.0 -- 0.1
ns ns ns ps ps ps ps Hz dB
CLKOUT RMS Jitter Generation FEC[1:0] = 00 (1/1 Scaling) CLKOUT Peak-Peak Jitter Generation FEC[1:0] = 00 (1/1 Scaling) Jitter Transfer Bandwidth (see Figure 6) Wander/Jitter Transfer Peaking
JGEN(RMS) JGEN(PP) FBW JP
12 kHz to 20 MHz 50 kHz to 80 MHz 12 kHz to 20 MHz 50 kHz to 80 MHz BW = 12,800 Hz < 12,800 Hz
Notes: 1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient. 2. For reliable device operation, temperature gradients should be limited to 10 C/min. 3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude for the Si5320 (tPT_MTIE) never reaches one nanosecond.
12
Rev. 2.3
Si5320
Table 4. AC Characteristics (PLL Performance Characteristics) (Continued)
(VDD33 = 3.3 V 5%, TA = -20 to 85 C)
Parameter
Symbol
Test Condition
Min
Typ
Max Unit
Acquisition Time
TAQ
RSTN/CAL high to CAL_ACTV low, with valid clock input and VALTIME = 0 Stable Input Clock; Temperature Gradient <10 C/min; 800 Hz Loop BW Stable Input Clock Selected until entering Digital Hold Constant Supply Voltage Constant Temperature When hitlessly recovering from Digital Hold mode 1/1 When hitlessly recovering from Digital Hold mode 6400 Hz, No Scaling 3200 Hz, No Scaling 1600 Hz, No Scaling 800 Hz, No Scaling
--
300
350
ms
Clock Output Wander with Temperature Gradient 1,2
CCO_TG
--
--
50
ps/ C/ min ppm
Initial Frequency Accuracy in Digital Hold Mode (first 100 ms with supply voltage and temperature held constant) Clock Output Frequency Accuracy Over Temperature in Digital Hold Mode Clock Output Frequency Accuracy Over Supply Voltage in Digital Hold Mode Clock Output Phase Step3 (See Figure 8)
CDH_FA
--
--
10
CDH_T CDH_V33 tPT_MTIE
-- -- -- -200
16.7 --
30 250
ppm /C ppm /V
0
200
ps
Clock Output Phase Step Slope3 (See Figure 8) BWSEL[1:0] = 11, FEC[1:0] = 00, DBLBW = 0 BWSEL[1:0] = 00, FEC[1:0] = 00, DBLBW = 0 BWSEL[1:0] = 01, FEC[1:0] = 00, DBLBW = 0 BWSEL[1:0] = 10, FEC[1:0] = 00, DBLBW = 0
mPT
-- -- -- --
-- -- -- --
10 5 2.5 1.25
ps/ s
Notes: 1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient. 2. For reliable device operation, temperature gradients should be limited to 10 C/min. 3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude for the Si5320 (tPT_MTIE) never reaches one nanosecond.
Rev. 2.3
13
Si5320
Table 5. Absolute Maximum Ratings
Parameter 3.3 V DC Supply Voltage LVTTL Input Voltage Maximum Current any output PIN Operating Junction Temperature Storage Temperature Range ESD HBM Tolerance (100 pf, 1.5 k) Symbol VDD33 VDIG Value -0.5 to 3.6 -0.3 to (VDD33 + 0.3) 50 -55 to 150 -55 to 150 1.0 Unit V V mA C C kV
TJCT TSTG
Note: Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Table 6. Thermal Characteristics
Parameter Symbol JA Test Condition Value Unit
Thermal Resistance Junction to Ambient
Still Air
20
C/W
0 -20 -40 -60 -80 -100 -120 -140 -160
Phase Noise (dBc/Hz)
10
1
10
2
10
3
10
4
10
5
10
6
10
7
10
8
Offset Frequency
Figure 4. Typical Si5320 Phase Noise (CLKIN = 155.52 MHz, CLKOUT = 622.08 MHz, and Loop BW = 800 Hz)
14
Rev. 2.3
Si5320
3.3 V Supply Ferrite Bead 0.1 F 2200 pF 22 pF
10 k 1%
33 F
VSEL33
REXT
VDD33
VDD25
GND
0.1 F CLKIN+ Input Clock Source 100 0.1 F Input Clock Frequency Select (19, 38, 77, 155, 311, or 622 MHz) FEC Scaling Select (14/15, 15/14) PLL Bandwidth Select Bandwidth Doubling Fixed Delay Mode Control LOS Validation Time Reset/Calibration Control CLKIN-
CAL_ACTV 0.1 F CLKOUT+ CLKOUT- 0.1 F
Calibration Active Status Output
Clock Output (19, 155, or 622 MHz) Clock Output Frequency Select
INFRQSEL[2:0] FEC[1:0] BWSEL[1:0] DBLBW FXDDELAY VALTIME RSTN/CAL LOS DH_ACTV
Si5320
FRQSEL[1:0]
Loss of Signal (LOS) Digital Hold Active
Figure 5. Si5320 Typical Application Circuit (3.3 V Supply)
Rev. 2.3
15
Si5320
2. Functional Description
The Si5320 is a high-performance precision clock multiplication and clock generation device. This device accepts a clock input in the 19, 38, 77, 155, 311, or 622 MHz range, attenuates significant amounts of jitter, and multiplies the input clock frequency to generate a clock output in the 19, 155, or 622 MHz range. Additional optional scaling by a factor of either 255/238 (15/14) or 238/255 (14/15) is provided for compatibility with systems that provide or require clocks that are scaled for forward error correction (FEC) rates. Typical applications for the Si5320 in SONET/SDH systems would be the generation and/or cleaning of 19.44, 155.52, or 622.08 MHz clocks from 19.44, 38.88, 77.76, 155.52, 311.04, or 622.08 MHz clock sources. The Si5320 employs Silicon Laboratories DSPLLTM technology to provide excellent jitter performance while minimizing the external component count and maximizing flexibility and ease-of-use. The Si5320's DSPLL phase locks to the input clock signal, attenuates jitter, and multiplies the clock frequency to generate the device's SONET/SDH-compliant clock output. The DSPLL loop bandwidth is user-selectable, allowing the Si5320's jitter performance to be optimized for different applications. The Si5320 can produce a clock output with jitter generation as low as 0.3 psRMS (see Table 4), making the device an ideal solution for clock multiplication in SONET/SDH (including OC-48 and OC192) and Gigabit Ethernet systems. The Si5320 monitors the clock input signal for loss-ofsignal, and provides a loss-of-signal (LOS) alarm when missing pulses are detected. The Si5320 provides a digital hold capability to continue generation of a stable output clock when the input reference is lost. This digital technology also allows for highly-stable and consistent operation over all process, temperature, and voltage variations. The benefits are smaller, lower power, cleaner, more reliable, and easier-to-use clock circuits.
2.1.1. Selectable Loop Filter Bandwidth
The digital nature of the DSPLL loop filter allows control of the loop filter parameters without the need to change external components. The Si5320 provides the user with up to eight user-selectable loop bandwidth settings for different system requirements. The base loop bandwidth is selected using the BWSEL [1:0] along with DBLBW = 0 pins. When DBLBW is driven high, the bandwidth selected on the BWSEL[1:0] pins is doubled. (See Table 7.) When DBLBW is asserted, the Si5320 shows improved jitter generation performance. DBLBW function is defined only when hitless recovery and FEC scaling are disabled. Therefore, when DBLBW is high, the user must also drive FXDDELAY high and FEC[1:0] to 00 for proper operation.
2.2. Clock Input and Output Rate Selection
The Si5320 provides a 1/32x, 1/16x, 1/8x, 1/4x, 1/2x, 1x, 2x, 4x, 8x, 16x, or 32x clock frequency multiplication function with an option for additional frequency scaling by a factor of 255/238 or 238/255 for FEC rate compatibility. Output rates vary in accordance with the input clock rate. The multiplication factor is configured by selecting the input and output clock frequency ranges for the device. The Si5320 accepts an input clock in the 19, 38, 77, 155, 311, or 622 MHz frequency range. The input frequency range is selected using the INFRQSEL[2:0] pins. The INFRQSEL[2:0] settings and associated output clock rates are given in Table 8. The Si5320's DSPLL phase locks to the clock input signal to generate an internal VCO frequency that is a multiple of the input clock frequency. The internal VCO frequency is divided down to produce a clock output in the 19, 155, or 622 MHz frequency range. The clock output range is selected using the Frequency Select (FRQSEL[1:0]) pins. The FRQSEL[1:0] settings and associated output clock rates are given in Table 9. The Si5320 clock input frequencies are variable within the range specified in Table 3 on page 7. The output rates scale accordingly. When a 19.44 MHz input clock is used with no FEC scaling enabled, the clock output frequency is 19.44, 155.52, or 622.08 MHz.
2.1. DSPLLTM
The Si5320's phase-locked loop (PLL) uses Silicon Laboratories' DSPLL technology to eliminate jitter, noise, and the need for external loop filter components found in traditional PLL implementations. This is achieved by using a digital signal processing (DSP) algorithm to replace the loop filter commonly found in analog PLL designs. This algorithm processes the phase detector error term and generates a digital control value to adjust the frequency of the voltagecontrolled oscillator (VCO). The technology produces low phase noise clocks with less jitter than is generated using traditional methods. See Figure 4 for an example phase noise plot. In addition, because external loop filter components are not required, sensitive noise entry points are eliminated, making the DSPLL less susceptible to board-level noise sources.
16
Rev. 2.3
Si5320
Table 7. Loop Bandwidth Settings
Loop Bandwidth BWSEL1 BWSEL0 DBLBW* 2.2.1. FEC Rate Conversion
12800 Hz 6400 Hz 6400 Hz 3200 Hz 3200 Hz 1600 Hz 1600 Hz 800 Hz
1 1 0 0 0 0 1 1
1 1 0 0 1 1 0 0
1 0 1 0 1 0 1 0
The Si5320 provides a 1/32x, 1/16x, 1/8x, 1/4x, 1/2x, 1x, 2x, 4x, 8x, 16x, or 32x clock frequency multiplication function with an option for additional frequency scaling by a factor of 255/238 or 238/255 for FEC rate compatibility. The multiplication factor is configured by selecting the input and output clock frequency ranges for the device. The additional frequency scaling by a factor of either 255/238 or 238/255 for FEC compatibility is selected using the FEC[1:0] control inputs. (See Table 10.) For example, a 622.08 MHz output clock (a non-FEC rate) can be generated from a 19.44 MHz input clock (a non-FEC rate) by setting INFRQSEL[2:0] = 001 (19.44 MHz range), setting FRQSEL [1:0] = 11 (32x multiplication), and setting FEC[1:0] = 00 (no FEC scaling). A 666.51 MHz output clock (a FEC rate) can be generated from a 19.44 MHz input clock (a non-FEC rate) by setting INFRQSEL[2:0] = 001 (19.44 MHz range), setting FRQSEL [1:0] = 11 (32x multiplication), and setting FEC[1:0] = 01 (255/238 FEC scaling). Finally, a 622.08 MHz output clock (a non-FEC rate) can be generated from a 20.83 MHz input clock (a FEC rate) by setting INFRQSEL[2:0] = 001 (19.44 MHz range), setting FRQSEL [1:0] = 11 (32x multiplication), and setting FEC[1:0] = 10 (238/255 FEC scaling).
*Note: When DBLBW = 1, FXDDELAY must be asserted and FEC scaling must be disabled.
Table 8. Nominal Clock Input Frequencies
Input Clock Frequency Range Reserved 622 MHz 311 MHz 155 MHz 77 MHz 38 MHz 19 MHz Reserved
INFRQSEL2 INFRQSEL1 INFRQSEL0
1 1 1 1 0 0 0 0
1 1 0 0 1 1 0 0
1 0 1 0 1 0 1 0
2.3. PLL Performance
The Si5320 PLL is designed to provide extremely low jitter generation, high jitter tolerance, and a wellcontrolled jitter transfer function with low peaking and a high degree of jitter attenuation.
2.3.1. Jitter Generation
Table 9. Nominal Clock Output Frequencies
Output Clock Frequency Range 622 MHz 155 MHz 19 MHz Driver Powerdown
FRQSEL1 FRQSEL0
1 1 0 0
1 0 1 0
Jitter generation is defined as the amount of jitter produced at the output of the device with a jitter free input clock. Generated jitter arises from sources within the VCO and other PLL components. Jitter generation is also a function of the PLL bandwidth setting. Higher loop bandwidth settings may result in lower jitter generation, but may also result in less attenuation of jitter on the input clock signal.
2.3.2. Jitter Transfer
Table 10. FEC Frequency Scalings
FEC Frequency Scaling 1/1 255/238 238/255 Reserved FEC1 FEC0
0 0 1 1
0 1 0 1
Jitter transfer is defined as the ratio of output signal jitter to input signal jitter for a specified jitter frequency. The jitter transfer characteristic determines the amount of input clock jitter that passes to the outputs. The DSPLL technology used in the Si5320 provides tightlycontrolled jitter transfer curves because the PLL gain parameters are determined by digital circuits that do not vary over supply voltage, process, and temperature. In a system application, a well-controlled transfer curve
Rev. 2.3
17
Si5320
minimizes the output clock jitter variation from board to board, providing more consistent system level jitter performance. The jitter transfer characteristic is a function of the BWSEL[1:0] setting. (See Table 7.) Lower bandwidth selection settings result in more jitter attenuation of the incoming clock but may result in higher jitter generation. Table 4 on page 9 gives the 3 dB bandwidth and peaking values for specified BWSEL settings. Figure 6 shows the jitter transfer curve mask.
Jitter Transfer Jitter Out (s) Jitter In 0 dB Peaking -20 dB/dec.
2.5. Hitless Recovery from Digital Hold
When the Si5320 device is locked to a valid input clock, a loss of the input clock causes the device to automatically switch to digital hold mode. When the input clock signal returns, the device performs a "hitless" transition from digital hold mode back to the selected input clock. That is, the device performs "phase build-out" to absorb the phase difference between the internal VCO clock operating in digital hold mode and the new/returned input clock. The maximum phase step size seen at the clock output during this transition and the maximum slope for this phase step are given in Table 4 on page 9. This feature can be disabled by asserting the FXDDELAY pin. When the FXDDELAY pin is high, the output clock is phase and frequency locked with a known phase relationship to the input clock. Consequently, any abrupt phase change on the input clock propagates through the device, and the output slews at the selected loop bandwidth until the original phase relationship is restored.
Note: When the DBLBW is asserted, hitless recovery must also be disabled by driving FXDDELAY high for proper operation.
F BW
f Jitter
Figure 6. PLL Jitter Transfer Mask/Template
2.3.3. Jitter Tolerance
Jitter tolerance for the Si5320 is defined as the maximum peak-to-peak sinusoidal jitter that can be present on the incoming clock. The tolerance is a function of the jitter frequency, because tolerance improves for lower input jitter frequency. See Figure 7.
Input Jitter Am plitude -20 dB/dec. 10 ns Excessive Input Jitter Range
mPT tPT_MTIE
Recovery from digital hold
F BW f Jitter In
Figure 8. Recovery from Digital Hold
Figure 7. Jitter Tolerance Mask/Template
2.6. Loss-of-Signal Alarm
The Si5320 has loss-of-signal (LOS) circuitry that constantly monitors the CLKIN input clock for missing pulses. The LOS circuitry sets a LOS output alarm signal when missing pulses are detected. The LOS circuitry operates as follows. Regardless of the selected input clock frequency range, the LOS circuitry divides down the input clock into the 19 MHz range. The LOS circuitry then over-samples this divided-down input clock to search for extended periods of time without input clock transitions. If the LOS
2.4. Digital Hold of the PLL
When no valid input clock is available, the Si5320 digitally holds the internal oscillator to its last frequency value. This provides a stable clock to the system until an input clock is again valid. This clock maintains very stable operation in the presence of constant voltage and temperature. The frequency accuracy specifications for digital hold mode are given in Table 4 on page 9.
18
Rev. 2.3
Si5320
circuitry detects four consecutive samples of the divided-down input clock that are the same state (i.e., 1111 or 0000), a LOS condition is declared, the Si5320 goes into digital hold mode, and the LOS output alarm signal is set high. The LOS sampling circuitry runs at a frequency of fO_622/8, where fO_622 is the output clock frequency when the FRQSEL[1:0] pins are set to 11. Table 3 on page 7 lists the minimum and maximum transitionless time periods required for declaring a LOS on the input clock (tLOS). Once the LOS alarm is asserted, it is held high until the input clock is validated over a time period designated by the VALTIME pin. When VALTIME is low, the validation time period is about 100 ms. When VALTIME is high, the validation time period is about 13 s. If another LOS condition is detected on the input clock during the validation time (i.e., if another set of 1111 or 0000 samples are detected), the LOS alarm remains asserted, and the validation time starts over. When the LOS alarm is finally released, the Si5320 exits digital hold mode and locks to the input clock. The LOS alarm is automatically set high at power-on and at every lowto-high transition of the RSTN/CAL pin. In these cases, the Si5320 undergoes a self-calibration before releasing the LOS alarm and locking to the input clock. The Si5320 also provides an output indicating the digital hold status of the device, DH_ACTV. The Si5320 only enters the digital hold mode upon the loss of the input clock. When this occurs, the LOS alarm will also be active. Therefore, applications that require monitoring of the status of the Si5320 need only monitor the CAL_ACTV and either the LOS or DH_ACTV outputs to know the state of the device.
VDD 2.5 V
100
100 CLKOUT- CLKOUT+ 15 mA
Figure 9. CLKOUT Equivalent Circuit, RSTN/ CAL asserted LOW
2.8. PLL Self-Calibration
The Si5320 achieves optimal jitter performance by using self-calibration circuitry to set the VCO center frequency and loop gain parameters within the DSPLL. Internal circuitry generates self calibration automatically on powerup or after a loss of power condition. Selfcalibration can also be manually initiated by a low-tohigh transition on the RSTN/CAL input. A self-calibration should be initiated after changing the state of the FEC[1:0] inputs. Whether manually initiated or automatically initiated at powerup, the self-calibration process requires the presence of a valid input clock. If the self-calibration is initiated without a valid clock present, the device waits for a valid clock before completing the self-calibration. The Si5320 clock output is set to the lower end of the operating frequency range while the device is waiting for a valid clock. After the clock input is validated, the calibration process runs to completion; the device locks to the clock input, and the clock output shifts to its target frequency. Subsequent losses of the input clock signal do not require recalibration. If the clock input is lost following selfcalibration, the device enters digital hold mode. When the input clock returns, the device re-locks to the input clock without performing a self-calibration. During the calibration process, the output clock frequency is indeterminate and may jump as high as 5% above the final locked value.
2.7. Reset
The Si5320 provides a Reset/Calibration pin, RSTN/ CAL, which resets the device and disables the outputs. When the RSTN/CAL pin is driven low, the internal circuitry enters into the reset mode, and all LVTTL outputs are forced into a high-impedance state. Also, the CLKOUT+ and CLKOUT- pins are forced to a nominal CML logic LOW and HIGH respectively (See Figure 9). This feature is useful for in-circuit test applications. A low-to-high transition on RSTN/CAL initializes all digital logic to a known condition and initiates self-calibration of the DSPLL. Upon completion of self-calibration, the DSPLL begins to lock to the clock input signal.
Rev. 2.3
19
Si5320
2.9. Bias Generation Circuitry
The Si5320 makes use of an external resistor to set internal bias currents. The external resistor allows precise generation of bias currents which significantly reduces power consumption and variation as compared with traditional implementations that use an internal resistor. The bias generation circuitry requires a 10 k (1%) resistor connected between REXT and GND. compensation circuit of one resistor and one capacitor to ensure stability over all operating conditions. Internally, the Si5320 VDD33 pins are connected to the on-chip voltage regulator input, and the VDD33 pins also supply power to the device's LVTTL I/O circuitry. The VDD25 pins supply power to the core DSPLL circuitry and are also used for connection of the external compensation circuit. The regulator's compensation circuit is in reality a resistor and a capacitor in series between the VDD25 node and ground. (See Figure 5 on page 15.) Typically, the resistor is incorporated into the capacitor's equivalent series resistance (ESR). The target RC time constant for this combination is 15 to 50 s. The capacitor used in the Si5320 evaluation board is a 33 F tantalum capacitor with an ESR of 0.8 . This gives an RC time constant of 26.4 s. The Venkel part number, TA6R3TCR336KBR, is an example of a capacitor that meets these specs. To get optimal performance from the Si5320 device, the power supply noise spectrum must comply with the plot in Figure 10. This plot shows the power supply noise tolerance mask for the Si5320. The customer should provide a 3.3 V supply that does not have noise density in excess of the amount shown in the diagram. However, the diagram cannot be used as spur criteria for a power supply that contains single tone noise.
2.10. Differential Input Circuitry
The Si5320 provides a differential input for the clock input, CLKIN. This input is internally biased to a voltage of VICM (see Table 2 on page 6) and may be driven by a differential or single-ended driver circuit. For differential transmission lines, the termination resistor is connected externally as shown.
2.11. Differential Output Circuitry
The Si5320 utilizes a current mode logic (CML) architecture to drive the differential clock output, CLKOUT. For single-ended output operation, simply connect to either CLKOUT+ or CLKOUT-, and leave the unused signal unconnected.
2.12. Power Supply Connections
The Si5320 incorporates an on-chip voltage regulator. The voltage regulator requires an external
Vn (V/Hz)
2100
42
f
10 kHz 500 kHz 100 Mhz
Figure 10. Power Supply Noise Tolerance Mask
20
Rev. 2.3
Si5320
2.13. Design and Layout Guidelines
Precision clock circuits are susceptible to board noise and EMI. To take precautions against unacceptable levels of board noise and EMI affecting performance of the Si5320, consider the following: Power the device from 3.3 V since the internal regulator provides at least 40 dB of isolation to the VDD25 pins (which power the PLL circuitry). Use an isolated local plane to connect the VDD25 pins. Avoid running signal traces over or below this plane without a ground plane in between. Route all I/O traces between ground planes as much as possible Maintain an input clock amplitude in the 200 mVPP to 500 mVPP differential range. Excessive high-frequency harmonics of the input clock should be minimized. The use of filters on the input clock signal can be used to remove highfrequency harmonics.
Rev. 2.3
21
Si5320
3. Pin Descriptions: Si5320
8 7 6 5 4 3 2 1
RSVD_NC
RSVD_NC
RSVD_NC
R SVD _N C
RSVD_NC
F E C [0 ]
F E C [1 ]
A
RSVD_NC
RSVD_G ND
R SVD _G N D
R SVD _N C
FXDDELAY
R SVD _G N D
R SVD _G N D
B W S E L [0 ]
B
RSVD_G ND
GND
GND
GND
GND
GND
VSEL33
B W S E L [1 ]
C
DH_ACTV
VDD25
VDD25
VDD33
VDD33
VD D 33
DBLBW
C L K IN +
D
C AL_AC TV
VDD25
VDD25
VDD33
VDD33
VD D 33
GND
C L K IN -
E
LO S
VDD25
VDD25
VDD25
VDD25
VD D 25
GND
IN F R Q S E L [0 ]
F
GND
GND
GND
GND
GND
GND
GND
IN F R Q S E L [1 ]
G
F R Q S E L [1 ]
CLKO UT-
C LKO U T+
F R Q S E L [0 ]
V A L T IM E
R S T N /C A L
REXT
IN F R Q S E L [2 ]
H
B o tto m V ie w
Figure 11. Si5320 Pin Configuration (Bottom View)
22
Rev. 2.3
Si5320
1 2 3 4 5 6 7 8
A
FEC[1]
FEC[0]
RSVD_NC
RSVD_NC
RSVD_NC
RSVD_NC
RSVD_NC
B
BWSEL[0]
RSVD_GND
RSVD_GND
FXDDELAY
RSVD_NC
RSVD_GND
RSVD_GND
RSVD_NC
C
BWSEL[1]
VSEL33
GND
GND
GND
GND
GND
RSVD_GND
D
CLKIN+
DBLBW
VDD33
VDD33
VDD33
VDD25
VDD25
DH_ACTV
E
CLKIN-
GND
VDD33
VDD33
VDD33
VDD25
VDD25
CAL_ACTV
F
INFRQSEL[0]
GND
VDD25
VDD25
VDD25
VDD25
VDD25
LOS
G
INFRQSEL[1]
GND
GND
GND
GND
GND
GND
GND
H
INFRQSEL[2]
REXT
RSTN/CAL
VALTIME
FRQSEL[0]
CLKOUT+
CLKOUT-
FRQSEL[1]
Top View
Figure 12. Si5320 Pin Configuration (Transparent Top View)
Rev. 2.3
23
Si5320
Table 11. Si5320 Pin Descriptions
Pin # Pin Name I/O Signal Level Description Fixed Delay Mode. Set high to disable hitless recovery from digital hold mode. This configuration is useful in applications that require a known, or constant, input-to-output phase relationship. When this pin is high, hitless switching from digital hold mode back to a valid clock input is disabled. When switching from digital hold mode to a valid clock input with FXDDELAY high, the clock output changes as necessary to re-establish the initial/ default input-to-output phase relationship that is established after powerup or reset. The rate of change is determined by the setting of BWSEL[1:0]. When this pin is low, hitless switching from digital hold mode back to a valid clock input is enabled. When switching from digital hold mode to a valid clock input with FXDDELAY low, the device enables "phase build out" to absorb the phase difference between the clock output and the clock input so that the phase change at the clock output is minimized. In this case, the input-to-output phase relationship following the transition out of digital hold mode is determined by the phase relationship at the time that switching occurs.
Note: FXDDELAY should remain at a static high or static low level during normal operation. Transitions on this pin are allowed only when the RSTN/CAL pin is low. FXDDELAY must be set high when DBLBW is set high.
B4
FXDDELAY
I*
LVTTL
D1 E1
CLKIN+ CLKIN-
I
AC Coupled System Clock Input. 200-500 mVPPD Clock input to the DSPLL circuitry. The frequency of (See Table 2) the CLKIN signal is multiplied by the DSPLL to generate the CLKOUT clock output. The input-to-output frequency multiplication factor is set by selecting the clock input range and the clock output range. The frequency of the CLKIN clock input can be in the 19, 38, 77, 155, 311, or 622 MHz range (nominally 19.44, 38.88, 77.76, 155.52, 311.04, or 622.08 MHz) as indicated in Table 3 on page 7. The clock input frequency is selected using the INFRQSEL[2:0] pins. The clock output frequency is selected using the FRQSEL[1:0] pins. An additional scaling factor of either 255/238 or 238/255 may be selected for FEC operation using the FEC[1:0] control pins.
*Note: The LVTLL inputs on the Si5320 device have an internal pulldown mechanism that causes these inputs to default to a logic low state if the input is not driven from an external source.
24
Rev. 2.3
Si5320
Table 11. Si5320 Pin Descriptions (Continued)
Pin # Pin Name I/O Signal Level Description Input Frequency Range Select. Pins(INFRQSEL[2:0]) select the frequency range for the input clock, CLKIN. (See Table 3 on page 7.) 000 = Reserved. 001 = 19 MHz range. 010 = 38 MHz range. 011 = 77 MHz range. 100 = 155 MHz range. 101 = 311 MHz range. 110 = 622 MHz range. 111 = Reserved. Loss-of-Signal (LOS) Alarm for CLKIN. Active high output indicates that the Si5320 has detected missing pulses on the input clock signal. The LOS alarm is cleared after either 100 ms or 13 seconds of a valid CLKIN clock input, depending on the setting of the VALTIME input. Digital Hold Mode Active. Active high output indicates that the DSPLL is in digital hold mode. Digital hold mode locks the current state of the DSPLL and forces the DSPLL to continue generation of the output clock with no additional phase or frequency information from the input clock. Reset/Calibrate. When low, the internal circuitry enters into the reset mode and all LVTTL outputs are forced into a highimpedance state. Also, the CLKOUT+ and CLKOUT- pins are forced to a nominal CML logic LOW and HIGH respectively. This feature is useful for in-circuit test applications. A low-to-high transition on RSTN/CAL initializes all digital logic to a known condition, enables the device outputs, and initiates self-calibration of the DSPLL. Upon completion of self-calibration, the DSPLL begins to lock to the selected clock input signal.
F1 G1 H1
INFRQSEL[0] INFRQSEL[1] INFRQSEL[2]
I*
LVTTL
F8
LOS
O
LVTTL
D8
DH_ACTV
O
LVTTL
H3
RSTN/CAL
I*
LVTTL
*Note: The LVTLL inputs on the Si5320 device have an internal pulldown mechanism that causes these inputs to default to a logic low state if the input is not driven from an external source.
Rev. 2.3
25
Si5320
Table 11. Si5320 Pin Descriptions (Continued)
Pin # Pin Name I/O Signal Level Description Differential Clock Output. High frequency clock output. The frequency of the CLKOUT output is a multiple of the frequency of the CLKIN input. The input-to-output frequency multiplication factor is set by selecting the clock input range and the clock output range. The frequency of the CLKOUT clock output can be in the 19, 155, or 622 MHz range as indicated in Table 3 on page 7. The clock output frequency is selected using the FRQSEL[1:0] pins. The clock input frequency is selected using the INFRQSEL[2:0] pins. An additional scaling factor of either 255/238 or 238/255 may be selected for FEC operation using the FEC[1:0] control pins. Clock Output Frequency Range Select Select frequency range of the clock output, CLKOUT. (See Table 3 on page 7.) 00 = Clock Driver Powerdown. 01 = 19 MHz Frequency Range. 10 = 155 MHz Frequency Range. 11 = 622 MHz Frequency Range. Forward Error Correction (FEC) Selection. Enable or disable scaling of the input-to-output frequency multiplication factor for FEC clock rate compatibility. The frequency of the CLKOUT output is a multiple of the frequency of the CLKIN input. The input-to-output frequency multiplication factor is set by selecting the clock input range and the clock output range. The clock output frequency is selected using the FRQSEL[1:0] pins. The clock input frequency is selected using the INFRQSEL[2:0] pins. An additional scaling factor of either 255/238 or 238/255 may be selected for FEC operation using the FEC[1:0] control pins as indicated below. 00 = No FEC scaling. 01 = 255/238 FEC scaling for all clock outputs. 10 = 238/255 FEC scaling for all clock inputs. 11 = Reserved.
Note: FEC[1:0] must be set to 00 when DBLBW is set high. *Note: The LVTLL inputs on the Si5320 device have an internal pulldown mechanism that causes these inputs to default to a logic low state if the input is not driven from an external source.
H6 H7
CLKOUT+ CLKOUT-
O
CML
H5 H8
FRQSEL[0] FRQSEL[1]
I*
LVTTL
A3 A2
FEC[0] FEC[1]
I*
LVTTL
26
Rev. 2.3
Si5320
Table 11. Si5320 Pin Descriptions (Continued)
Pin # Pin Name I/O Signal Level Description Bandwidth Select. BWSEL[1:0] pins set the bandwidth of the loop filter within the DSPLL to 6400, 3200, 1600, or 800 Hz as indicated below. 00 = 3200 Hz 01 = 1600 Hz 10 = 800 Hz 11 = 6400 Hz
Note: The loop filter bandwidth will be twice the value indicated when DBLBW is set high.
B1 C1
BWSEL[0] BWSEL[1]
I*
LVTTL
E8
CAL_ACTV
O
LVTTL
Calibration Mode Active. This output is driven high during the DSPLL self-calibration and the subsequent initial lock acquisition period. Clock Validation Time for LOS. VALTIME sets the clock validation times for recovery from an LOS alarm condition. When VALTIME is high, the validation time is approximately 13 seconds. When VALTIME is low, the validation time is approximately 100 ms. Reserved--GND. This pin must be tied to GND for normal operation. Reserved--No Connect. This pin must be left unconnected for normal operation. Select 3.3 V VDD Supply.
H4
VALTIME
I*
LVTTL
B2, B3, B6, B7, C8 A4-8, B5, B8
RSVD_GND RSVD_NC
-- --
LVTTL LVTTL
C2
VSEL33
I*
LVTTL
This is an enable pin for the internal regulator. To enable the regulator, connect this pin to the VDD33 pins. D3-D5, E3-E5 VDD33 VDD Supply
3.3 V Supply. 3.3 V power is applied to the VDD33 pins. Typical supply bypassing/decoupling for this configuration is indicated in the typical application diagram for 3.3 V supply operation. 2.5 V Supply. These pins provide a means of connecting the compensation network for the on-chip regulator.
D6, D7, E6, E7, F3-F7
VDD25
VDD
Supply
*Note: The LVTLL inputs on the Si5320 device have an internal pulldown mechanism that causes these inputs to default to a logic low state if the input is not driven from an external source.
Rev. 2.3
27
Si5320
Table 11. Si5320 Pin Descriptions (Continued)
Pin # Pin Name I/O Signal Level Description Ground. Must be connected to system ground. Minimize the ground path impedance for optimal performance of the device. External Biasing Resistor. Used by on-chip circuitry to establish bias currents within the device. This pin must be connected to GND through a 10 k (1%) resistor. Double Bandwidth Active high input to boost the selected bandwidth 2x. When this pin is high, the loop filter bandwidth selected on BWSEL[1:0] is doubled. When this pin is high, FXDDELAY must also be high and FEC[1:0] must be 00.
C3-C7, E2, F2, G2-G8
GND
GND
Supply
H2
REXT
I
Analog
D2
DBLBW
I*
LVTTL
*Note: The LVTLL inputs on the Si5320 device have an internal pulldown mechanism that causes these inputs to default to a logic low state if the input is not driven from an external source.
28
Rev. 2.3
Si5320
4. Ordering Guide
Part Number Package Temperature
SI5320-X-BC
63-Ball CBGA
-20 to 85 C
Note: "X" denotes product revision.
Rev. 2.3
29
Si5320
5. Package Outline
Figure 13 illustrates the package details for the Si5320. Table 12 lists the values for the dimensions shown in the illustration.
Figure 13. 63-Ball Ceramic Ball Grid Array (CBGA)
Table 12. Package Drawing Dimensions
Dimension Description Minimum Nominal Maximum
A A1 A2 A3 b D D1 e S
Total Package Height Standoff Ceramic Thickness Mold Cap Thickness Solder Ball Diameter Ceramic Body Size Mold Cap Size Solder Ball Pitch Pitch to Centerline
2.13 0.60 0.88 0.55 0.65 8.85 8.55
2.28 0.70 0.98 0.60 0.70 9.00 8.75 1.00 BSC 0.50 BSC
2.43 0.80 1.08 0.65 0.75 9.15 8.95
30
Rev. 2.3
Si5320
6. 9x9 mm CBGA Card Layout
Placement Courtyard
Table 13. Recommended Land Pattern Dimensions
Symbol Parameter Min Dimension Nom Max Notes
C D E F X
Column Width Row Height Pad Pitch Placement Courtyard Pad Diameter
-- -- -- 10.00 0.64
7.00 REF 7.00 REF 1.00 BSC -- 0.68
-- -- -- -- 0.72 1 2, 3
Notes: 1. The Placement Courtyard is the minimum keep-out area required to assure assembly clearances. 2. Pad Diameter is Copper Defined (Non-Solder Mask Defined/NSMD). 3. OSP Surface Finish Recommended. 4. Controlling dimension is millimeters. 5. Land Pad Dimensions comply with IPC-SM-782 guidelines. 6. Target solder paste volume per pad is 0.065 mm3 0.010 mm3 (4000 mils3 600 mils3). Recommended stencil aperture dimensions to achieve target solder paste volume are 0.191 mm thick x 0.680.01 mm diameter, with a 0.025 mm taper. 7. Recommended stencil type is chemically etched stainless steel with circularly tapered apertures.
Rev. 2.3
31
Si5320
DOCUMENT CHANGE LIST
Revision 2.0 to Revision 2.1
Updated Figure 8, "Recovery from Digital Hold," on page 18. Updated Figure 13, "63-Ball Ceramic Ball Grid Array (CBGA)," on page 30. Updated Table 12, "Package Diagram Dimensions," on page 30 Added Figure 4, "Typical Si5320 Phase Noise (CLKIN = 155.52 MHz, CLKOUT = 622.08 MHz, and Loop BW = 800 Hz)," on page 14
Revision 2.1 to Revision 2.2
Updated "2.7. Reset" on page 19. Updated Table 12, "Package Diagram Dimensions," on page 30.
Revision 2.2 to Revision 2.3
Updated "5. Package Outline" on page 30.
32
Rev. 2.3
Si5320
NOTES:
Rev. 2.3
33
Si5320
CONTACT INFORMATION
Silicon Laboratories Inc.
4635 Boston Lane Austin, TX 78735 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Email: productinfo@silabs.com Internet: www.silabs.com
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories, Silicon Labs, and DSPLL are trade-marks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
34
Rev. 2.3

▲Up To Search▲

Price & Availability of SI5320-X-BC

	To Download SI5320-X-BC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .